Autel EVO Max 4T / 4N RTK Setup: Custom NTRIP
Connect the Autel EVO Max 4T, 4N and Alpha to RTKdata NTRIP. Enable RTK, choose Custom Network RTK, then enter host, port and AUTO mountpoint.
Connect Autel's current enterprise drones: the EVO Max 4T, EVO Max 4N, and Autel Alpha: to RTKdata.com's NTRIP correction service for centimeter-level positioning.
Requirements
Aircraft: EVO Max 4T or 4N with the EVO Max RTK Module installed, or Autel Alpha (built-in RTK)
Controller: Autel Smart Controller V3
Software: Autel Enterprise App, updated to the latest version
Firmware: Aircraft, RTK module (if applicable), and controller firmware updated to the latest version: version mismatches commonly break RTK
Internet: Wi-Fi hotspot tethered to the controller (the controller relays the correction stream)
RTKdata account: Active subscription with NTRIP credentials
Step-by-step setup
Enter NTRIP connection settings
Select your region and enter the corresponding server details:
Host (domain):
rtk.rtkdata.comHost (IP fallback):
13.56.117.10Port:
2101Username / Password: From RTK Credentials in the internal dashboard (not website login)
Mountpoint (ALL CAPS):
AUTO(recommended), orAUTO_WGS84,AUTO_ITRF2020,AUTO_ITRF2014
Host (domain):
eu.rtkdata.comHost (IP fallback):
3.73.41.96Port:
2101Username / Password: From RTK Credentials in the internal dashboard (not website login)
Mountpoint (ALL CAPS):
AUTO(recommended), orAUTO_WGS84,AUTO_ITRF2020,AUTO_ITRF2014
Host (domain):
aus.rtkdata.comHost (IP fallback):
54.206.56.130Port:
2101Username / Password: From RTK Credentials in the internal dashboard (not website login)
Mountpoint (ALL CAPS):
AUTO(recommended), orAUTO_WGS84,AUTO_ITRF2020,AUTO_ITRF2014
Enter the mountpoint AUTO manually (in ALL CAPS) rather than relying on a station list: RTKdata's AUTO is keyed to your position, not a fixed station.
Connect and verify Fix
Save/apply the settings to connect.
Place the drone outdoors in an open area so the RTK system acquires satellites.
Watch the RTK status in the live view:
SINGLE
Basic GNSS fix. No corrections applied yet.
FLOAT
Corrections received and processing. Accuracy improving.
FIX
Centimeter-level accuracy active (~1 to 2 cm).
Convergence typically takes 30 to 90 seconds in open sky.
Vertical reference (heights)
Troubleshooting
Won't connect to caster
"Network RTK" selected instead of Custom
Switch the correction source to Custom
No RTK option at all
EVO Max RTK Module not installed/detected
Install the module (EVO Max) and confirm firmware is current; Alpha has built-in RTK
No corrections / stuck on Float
Drone indoors or no satellite fix → no GGA sent
Move outdoors to open sky so the aircraft acquires satellites and reports position
No corrections
No internet on the controller
Verify the Smart Controller V3 hotspot tether
Authentication fails
Wrong credentials
Re-enter username/password from the RTKdata dashboard (case-sensitive, username starts with rtk)
RTK keeps dropping
Firmware mismatch (aircraft / module / controller)
Update all three to the latest firmware
Tips
EVO Max needs the RTK module; Alpha has RTK built in. First check which hardware you have.
Always pick "Custom" for RTKdata: "Network RTK" is a non-functional legacy option.
Enter
AUTOmanually in ALL CAPS as the mountpoint.Firmware first. Mismatched aircraft/module/controller firmware is the most common RTK failure on this platform.
Different app from EVO II. EVO Max/Alpha use the Autel Enterprise App; the EVO II line uses Autel Explorer: don't reuse those screenshots.
Related Guides
Autel EVO II Pro RTK V3: the older EVO II line, configured in Autel Explorer rather than the Enterprise App
NTRIP & GGA Essentials: why the caster needs your GGA position and how the
AUTOmountpoint picks the nearest reference stationUnderstanding Heights: converting the ellipsoidal heights in your mapping output to orthometric heights
Drones & UAVs: all drone platforms with an RTKdata setup guide
Related Industry Solutions
Last updated
Was this helpful?